Zdravím,
Laboruji tady zrovna s WRT-311, pokud by se někomu hodila konzole pro zotavení tak tady je návod:
Připojení:
sys konektor s označením J4
Při pohledu od portu:
1 - VCC (3,2V)
2 - TX
3 - RX
4 - GND
nastavení terminálu:
Rychlost 38400
8 bit
žádná parita
1 stop bit
Xon/Soft
A hurá na to!
Po připojení vypíše asi něco takového:
UART1 output test ok
Uart init
mfid=000000c2 devid=00002249
Found 1 x 2M flash memory
---RealTek(RTL8186)at 2005.09.14-18+0800 version 1.3b (180MHz)
no sys signature at 00010000!
Jump to image start=0x80300000...
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
early printk enabled
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock1 console=0 single
Calibrating delay loop... 178.99 BogoMIPS
Memory: 14252k/16384k available (1604k kernel code, 2132k reserved, 128k data, 4
8k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
check_wait... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Serial driver version 6.02 (2003-03-12) with no serial options enabled
ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1
state->flags=00000000
Realtek GPIO Driver for Flash Reload Default
block: 64 slots per queue, batch=16
PPP generic driver version 2.4.1
PPP MPPE Compression module registered
RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
Found 1 x 2M Byte MXIC MX29LV160AB at 0xbe000000
Creating 2 MTD partitions on "DiskOnChip Millennium":
0x00000000-0x00100000 : "boot+cfg+linux"
0x00100000-0x00200000 : "root fs"
RTL8185 driver version 1.9 (2006-03-16)
8186NIC Ethernet driver v0.0.5 (Mar 3, 2006)
eth0: RTL8186-NIC at 0xbd200000, 00, IRQ 4
eth1: RTL8186-NIC at 0xbd300000, 04, IRQ 5
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
ip_conntrack version 2.1 (128 buckets, 1024 max) - 312 bytes per conntrack
PPTP netfilter connection tracking: registered
PPTP netfilter NAT helper: registered
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 48k freed
mount /proc file system ok!
mount /var file system ok!
init started: BusyBox v1.1.0-pre1 (2006.05.29-20+0000) multi-call binary
BusyBox v1.1.0-pre1 (2006.05.29-20+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Setting opmode
Killing tasks then interfaces
Setting MACs
Setup bridge(s)
device eth0 entered promiscuous mode
eth0 is 8305
device wlan0 entered promiscuous mode
device eth1 entered promiscuous mode
eth1 is 8305
br0: port 2(wlan0) entering disabled state
device wlan0 left promiscuous mode
br0: port 3(eth1) entering listening state
br0: port 1(eth0) entering listening state
br0: port 3(eth1) entering learning state
br0: port 3(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering learning state
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
Setting up IP
Starting services
Setting Routes
Setting up Firewall
#
Jinak pokud by mi někdo poradil jak uložit změnu MAC adresy po rebootu byl bych vděčny
Hodně zdaru!
